Corrosion Resistance Paint

Product Detail

725-H52-77 Epoxy High Build Anticorrosive Coating-Grey

 

Product Description		-This is a two-component high build polyamide adduct cured universal epoxy paint
		-Excellent anticorrosive and very good mechanical properties.
		-Short drying time and applying at low temperature.
		-Excellent adhesion on low roughness substrate.
		-VOC less than 250g/L
Intended Uses		-As high performance coating for offshore structures, petrochemical plants, paper mills and bridges.
		-Intended for fast cure and for in-shop applications where fast recoating and handling is required.
Product Information	Volume Solids	75%±2%
	Finish/Sheen	Gloss
	Typical Film Thickness	125 microns dry (166microns wet)
	Theoretical Coverage	6.0m2/L at typical film thickness
	Mix Ratio	3.4:1(volume)6:1(mass)
	Method of Application
	Airless Spray	Recommended
		Tip size range						0.45-0.68mm
		Output pressure						=17MPa
	Air Spray	Not recommended
	Brush/Roller	For small area only
	Thinner	Not recommended. Use only in exceptional circumstances (volume 5%)
	Cleaner	HX-501
	Induction Period	-10?	5?			10?
		30min	15min			10min
	Drying Information
		-10?		5?			20?			30?
	Touch Dry	18h		9h			2h			1.5h
	Hard Dry	42h		20h			4.5h			3.5h
	Pot Life	4h		3h			2h			1h
	Overcoating Data          Substrate Temperature
	Overcoated by    725-H52-77	-10?	5?			25?			30?
		Min Max	Min Max			Min Max			Min Max
		50h 90d	20h 60d			5h  30d			4h  25d
	725-H53-87	50h 90d	20h 60d			5h  30d			4h  25d
	725-BS43-91	50h	36h			20h			10h
	?? Storage	Store in cool and dry conditions. Well ventilate. Keep away from hot and fire. Shelf Life: 12 months minimum at 25?. Subject to re-inspection thereafter.
	Pack Size	Part A			25.2 kg/15.5L in 20L container
		Part B			4.2kg/4.5L in 6L container
	Flash Point	Part A			Greater than 31?
		Part B			Greater than 29?
		Mixed paint			Greater than 31?
Systems and Compatibility	Consult your Sunrui Representative for the systems best suited for the surfaces to be protected.
Surface Preparation	All surfaces to be coated should be clean, dry and free from contamination.      Abrasive Blast Cleaning   Abrasive blast clean to Sa2½(GB/T 8923.1-2011). If oxidation has occurred between blasting and application of 725-H52-77, the surface should be reblasted to the specified visual standard.   Surface defects revealed by the blast cleaning process should be ground. Filled, or treated in the appropriate manner.      Shop Primed Steelwork   Weld seams and damaged areas should be blast cleaned to Sa2½(GB/T 8923.1-2011).   If the shop primer shows extensive or wildly scattered breakdown overall sweepblasting may be necessary.     Repair The areas to be repaired should be cleaned to St3(GB/T 8923.1-2011)by  mechanical method or higher level of surface prepared to Sa2.5(GB/T 8923.1-2011)by abrasive blasting. Abrade the area immediately surrounding the repair to provide a key for subsequent coating application. Overlap areas should be kept to a minimum.
Limitations	Apply in good weather. Temperature of the surface to be coated must be least 3? above the dew point when the is lower than 85%.   In common with all epoxy base coatings, 725-H52-77 will exhibit chalking of the firm on UV exposure.   The dry time and overcoating interval may change according to the environment factors.   Avoiding absorb the solvent steam and paint steam for long time. Skin and eyes must avoid contacting the paint. Pay attention to ventilate and fireproof when applying.
Duty statement	The data in the sheet base on the information from the laboratory and practice. The application may exceed the control, so we only ensure our product quality. We own the right of the data sheet modification without informing.